Can you confirm that the 67 ft/lbs is for the torx bolts?? If it's not a typo in the book, "comfortable" ain't got nothin' to do with it. Location: Abbotsford BC Canada. Strap Clip (rear Driveshaft to the carrier bearing). I assume you dont go around and prob like a rim torque pattern. Any damage to the boot, or any loss or damage to any of the boot clamps, will require the replacement of the entire boot kit assembly. Initially, their parts manager said they were listed at around $5 each. When I removed the drive shaft the nuts were not very tight but I'm thinking they should be and maybe a little lock-tight on the bolts as well? Drive shaft bolt torque specs ft lbs. 02-29-2016, 03:06 PM||# 8|. Get a MAP gas bottle/torch at ACE or somewhere (unless you have a oxy/acetelene setup) to melt out the nylon that holds the cups in.
Hey guys im wondering whats the exact torque spec for front differential connection and the transfer case connection? 04-15-2011 10:26 PM. 26 ft-lbs is already at the upper end of my comfort level and is hard enough for me to twist with that much force on those tiny bolts waiting for the 'click' without wincing. I'm Trying To Take Off My Drive Shaft But It Is Not Moving. Torque Spcs - PLEASE HELP. I have been all over the internet looking for torque specs for the various components for my rear driveshaft... No additional grease needs to be added. Unfortunate, I will removing the new ford spicer u joint and adding 2 SS washers as there is about 1. The bolts aren't listed in any of the online Mercedes parts catalogs. Trust Spicer® lubricant to protect your universal joint and slip assemblies.
That is where it discerns between the transmission outputor driveshaft flange and the differentialor pinion flange and it gives the torque specs for each flange. So I will be doing headers this weekend and I'm AWD and from what I hear I have to drop the front drive shaft. The best source for this information is found in a service manual, if you cannot afford one your public library will often have automotive service manuals available to check out for free. With vehicle in neutral, position vehicle on hoist. Install rear C/V joint bolts (1) and tighten to 30 N m. 5. After installation into a driveshaft, and prior to being placed into service, you must (with the exception of Service-Free U-joints) lubricate each u-joint kit in accordance with the following recommendations: - Apply grease gun pressure to each u-joint until fresh grease appears at each bearing seal. Related Drive Shaft Bolt Content. Anyway - I want to make sure the bolts on the coupler have not loosened and if tightening them makes the noise go away - I'll replace them. Another JR. Torque spec for rear drive shaft. - Megalomegalodon. 03-01-2016, 07:45 AM||# 9|. Sorry, I'm using my phone so I can't see sigs and don't know the specifics of your truck. But it's what the manual says. Location: Huntingdon. Please refer to bulletin JOI-TEC-56 for installation procedures which can be found in the Spicer Literature Library.
In order to minimize the potential for driveline failure, including driveline separation, you must: - Carefully review the lubrication specifications on this web page and lube manual located here. On half round type yokes with bearing retainers or bearing straps: - Release pressure by removing the retainer or strap and unhooking the end of the driveshaft from the yoke ears. Spicer ultra-premium synthetic grease is compatible with all NLGI-2 greases, and delivers professional-grade quality, even at high temperatures. They were not anywhere near as tight as I thought they would be. Drive shaft bolt torque specs. © 1999 - 2023 2CarPros, Inc. I would think it's similar to the HPOP fittings. 5 mm or movement in the brand new part. CAUTION: ALWAYS replace any loosened or removed bolt with a NEW BOLT. Brakes, Steering, Suspension, Tires, & Wheels. NOW the actual single bolt on the Yolk that holds the carrier bearing on the front part of the drive shaft. You could probably inspect the old bolts and see that it was previously used on the threads.
Now most mechanics use a tried and true method of knowing when enough is enough. Location: Greater Boston. 1999 Ford F-150 Driveshaft. Recently Browsing 0 members.
I Have Seen Plenty Of Videos Regarding The Drop Down Of The Single Piece Driveshafts On Some Models Of The F150 To Service The Slip Yoke For... Are the four nuts that connect to the ebrake and the rear differential the joint yoke retainer nuts I see in my FSM at 160 ft-lbs.? Wipe a liberal coating of the same grease into the each bearing assembly, filling all of the cavities between the needle rollers. Tubes (SPL1051), and 1-gal. Just use a good 6 point closed end wrench and you should be fine.
MB Dealer that does Sprinters. I used the search and couldn't come up with a exact answer.... Align marks on the companion flanges with the. © 2023 MH Sub I, LLC dba Internet Brands. I don't know but 76 ft/lbs sounds a bit much for those little bolts, are you sure about that? Maybe we will when we re-install. Does anyone know what I torque the adapter plate and the driveshaft to? As far a torque specifications you will not find reliable information online. So... it is more accurate to torque the bolt to a low known value (where friction hasn't yet become a significant factor) to provide a known starting point, and then use degrees of tightening (vs. applied torque) after that to arrive at the final torque setting. Visual compare is one thing, compare bolt markings in another and more complex comparison how they actually perform. Did I read that correct. 1997 Ford Ranger 4x4 3. I cant believe some idiot in that thread thought the xzn triple square fasteners are the same thing as a 12 point fastener.
Ahh sorry I re-read. Communicate privately with other Tacoma owners from around the world. Spicer® XC™ Center Bearing Lubrication Procedure. Spicer® greasable u-joint kits contain only enough grease to provide needle bearing protection during storage. NO IDEA what the torque is here for these little 4 bolts.