Upper Manifold bolts – 89 in lbs –. Maybe a mod here can delete it. 6L V6 Chrysler 200, Town & Country, Dodge Grand Caravan, Jeep Grand Cherokee, Wrangler, Ram 1500, 2500. Use the fitment form at the top of the page to select your exact year and engine type for your Jeep Wrangler. Engine Oil Cooler and Filter Housing Adapter Kit - Replaces 68105583AF, 68105583AE - Fits 3. Oil Filter Adapter/Cooler. NOTE: After removing the upper intake, I strongly recommend covering the lower intake holes and using an air gun to blow any debris out from the sides of the lower intake. Clean out all old oil from the oil filter/cooler housing mounting valley. Most recently I purchased a wiper transmission for my Wrangler - a discontinued Mopar part. Engine oil cooler for 2016 jeep wrangler. Remove all 7 upper intake bolts as listed in the provided All-DATA pages. Procedural Steps: - Remove Plastic Engine Cover – Lift and pull forward.
Here at Advance Auto Parts, we work with only top reliable Engine Oil Filter Housing product and part brands so you can shop with complete confidence. After driving your JK for a good period of time, I would check for any new leaks. Both sides are held on by a pipe clamp and can either be taken off with a flat head screw driver or an 8mm socket. Mechanic comes to you. Ordered a new Oil cooler assembly using the Dorman aluminum housing that will update the filter to the late style 14 & up. Using a T30 Torx driver remove (4) bolts holding fuel rails on the engine. This replacement Oil Filter Housing Adapter Kit also comes with a new oil filter pre-installed for a complete and worry free installation. Jeep 3.6 oil cooler upgrade. I was able to carefully remove all the fuel injector plugs with a screw driver.
Remove (3) lines on passenger (right) side of upper intake. Carefully remove the fuel rails from the passenger side fuel injectors and then the driver side fuel injectors. I used a brake pump with reservoir to remove the oil from the valley and then used needle noise pliers to dab small pieces of rag and soak up the rest of the oil. We're sure you will get the right product to keep that Wrangler running for a long time. The valley is fairly deep as well, so there is quite a bit of oil. Oil Cooler Housing Upgrades. We offer a full selection of genuine Jeep Wrangler Oil Coolers, engineered specifically to restore factory performance. Using the same lubricant lightly lube the fuel rail injector connections.
I have a question: Is there a redesigned or aftermarket/race part that I could use INSTEAD of going back with the dumbf**k plastic part? I was able to see a little bit of pooled oil looking in between the oil filter housing and the intake. Small flat tip screwdriver. Maneuver the oil filter/cooler housing up and out, once free of the engine unplug the wiring for the oil pressure sensor and Oil Temperature Sending unit on the back of the housing and the pinch clamp for the cooling line. There is a wiring harness attached to the back of the lower intake with a ziptie clip. Jeep Wrangler Engine Oil Filter Housing | Advance Auto Parts. Norwegian Krone (NOK). ALL THE PARTS YOUR CAR WILL EVER NEED. Remove (2) clips on rear of the upper intake on the passenger side. This oil filter housing adapter kit is NOT a genuine Chrysler, Dodge, Jeep, Ram or Mopar part.
I also would recommend some masking tape for when the intake is off so you can cover the intake ports to the heads (VERY vulnerable to foreign objects when exposed). This is a basic Write-Up on how to repair the common oil cooler housing/adaptor leak. Upper to lower intake bolts – 106 in lbs. New Zealand Dollars (NZ$).
Easy, You will see MOTOR oil on your upper and lower transmission bell housing. How will you know if your oil cooler is leaking? Torque Sequence (Front #1, Back #2, Middle #3). Jeep cherokee oil cooler. Wide painters take is very effective. Product seems way better made than original plastic housing which was leaking oil. The oil filter should also be changed to maximize debris removal. Oil will accumulate debris over time, to the point where deposits may narrow an oil coolers thin galleries. I unplugged the harness connector and bent the bracket up and out of the way. You will only get around a gallon out, maybe less.
I used a deep well 8mm and 10mm socket for the whole job with a few different extensions and a wobble socket attachment. Remove 2 plastic body clips (on back of the upper intake). Use dielectric or silicone based lubricant on the injector o-rings to more easily install them, plug injectors back in and seat firmly. 3.6L Oil Filter/Cooler Adaptor Housing Replacement. It is what i would use when the day happens, no question. I removed the 10mm bolt on each side in order to remove the two brackets. South Korean Won (₩). Once the bolt studs are past the bracket and you can lift up, you should be able to pull the upper intake up and out towards the driver side. Close the petcock and move your bucket underneath in the middle touching your axle. Might as well get new while you have car torn up.
The hose is help on by a single clamp that can be removed with pliers. This will help keep unwanted debris out of the intake port after pulling the lower intake off. Canadian Dollars (CAD$). Remove Vent hose behind Map Sensor location. Free 50 point safety inspection. Remove the radiator cap and open the radiator petcock with a clean bucket underneath. Atomic: I have an appointment with the dealer to get it fixed, and it's a 100 dollar deductible so it's not a big deal but... Remove foam from behind the upper intake at firewall. The block side intake manifold openings are very sharp, be careful not to get cut. By the way 19GCTrailhawk sorry, i meant to give you a like but don't exactly know how it happened it ended up with a instead.