Well piping pitless adapters eliminate the need for a well pit to protect pipes from freezing. Also, DON'T DRAIN THE BLEACH WATER INTO THE LEECH FIELD FOR YOUR SEPTIC SYSTEM. When ready to make the electrical connections, make sure to put the heat shrink plastic onto each wire before making the crimp connections. Build Robby: Replacing Well Pump And Unlocking Pitless Adapter. One of the things that happens with older wells is that, over a period of several years, silt from the aquifer can seep into the bottom of the casing. BEFORE YOU DO ANYTHING WITH THE WELL CAP MAKE SURE YOU KILL THE POWER AT THE WELL PUMP CIRCUIT BREAKER!!! Then purge the inside of the house.
So the pump installer ends up with, in effect, a scrap pile of short sections of pipe. And there are special tools that contractors have to lift the pump from that kind of depth. That's exactly the sort of thing you need to know when you're buying a replacement. For Maass JX1 and Model MB Pitless Units. If you do not have water after 5 minutes; shut off the breaker to the pump. Post your water well and pump questions. Dogs are really helpful to have around when doing a job like this. Place the pump near the hole and move the water flex pipe so it is in a straight line to the well head.
Proper chlorination requires 3 pints of 5% chlorine bleach per 100 gallons of water in the well, PLUS 3 pints of the same to sanitize the plumbing inside the house. Once you get them all off, set them in a safe place for later. I didn't search before I got in the car. Should you have any abrupt elbow fittings, they must be replaced with pipe to create sweeping bends to allow the heating cable to pass. As I mentioned above, the connectors are usually brass. Pipe dope isn't always safe for potable water, so it's recommended that you just stick with Teflon. As a result, most Heat-Line systems, including Retro-Line can be installed by homeowners; however, Heat-Line commonly recommends that a qualified tradesperson complete the installation process. This certification and feature are unmatched by standard electric heat tape for pipes with thermostats, pipe heater wires, heat trace tapes, and plumbing heat tapes. On 2017-12-12 2 by CM. Old style removal old style pitless adapter plates. Thanks to mine, we were able to hose off the motor to find out exactly what the specs were.
Q- Is there a maximum length of Retro-Line heating cable systems? In order to pull all of this stuff out of the well, you need a special tool called a "pitless adapter wrench. " The first number is the psi at which the switch will sense the pressure in the system is too low, and it will turn the pump on. You'll also see your safety rope, and the electrical wires that power the motor. 3) The safety rope, which is tied directly to the well pump and keeps it from falling down into "the abyss" if anything goes wrong. Dear Maass Midwest Customer, The new price list reflects a slight increase in our Model 531 Check valves, the Well Buster packers, the Cycle Slayer and the tool, thread compounds. Once heat shrunk, tape the wires to the pipe to keep them from moving freely in the pipe. This article is about one of my favorite subjects, as you may have guessed, the pitless adapter. Then you can finish inserting the pitless adapter back into place. To completely shut off the system it must be unplugged or installed with a thermostat. Q – Does the unit shut off when not required? Another Chapter on Pitless Adapters | 2016-02-01 | The Driller. Homeowners are encouraged to contact a local contractor for the purchase and installation of the equipment and products sold by Milby Company. Some people may read this and wonder, "What is a check valve? "
If not, what can be done? Hi guys, I was at work the other day (I drill wells and install pumps and pressure tanks) and thought to myself, this might be something useful to take to the gj boards. Pitless connectors have to be located BELOW the frost line for your area. Old style removal old style pitless adapter home depot. It should come with two connectors and some heat-shrink material. The advanced self-regulating technology employed in the Retro-Line product renders it safe for use with plastic pipes even when dry as it can never overheat and damage the pipe. Without the need for a pit, the adapter is appropriately named a Pit-less adapter. Most houses are recommended to have a pump that will support 5 gallons per minute. ) If you have a 3rd person, they can assist the first person with pulling out the well pump as it can get tiring for some people.
After this is accomplished the required length of Retro-Line can be measured and installed to freeze-protect the pipe to a point below the lake ice near the shoreline. Click to enlarge any image]. When you turn on the water to wash your hands or flush your toilet, the amount of water stored in the pressure tank is reduced. 7] X Trustworthy Source State of Indiana Official site for state-approved sources related to life in Indiana, including laws, services, and culture Go to source. In my case, I'm going to guess that it's about 70' of total water space in a 6" tube. Old style removal old style pitless adapter wrench. DO NOT CUT HEATING CABLE or POWER LEAD. It's not pictured, but I also secured the electrical wiring and the safety rope to the water line by wrapping it with electrical tape at 12-18" intervals. Put the cap back on and go inside. Feed the pump back into the casing slowly, using the safety rope. Remember, you don't want to have to remove the pump once it is down in the pipe just because of a bad connection. If you're doing something like this on your own, wider is better!
5 gallons per foot of depth of a well using a 6" well casing - but remember you have to find the height of water column available to the pump. Bottom line: There was no way to clean this out, so a new water line went on the shopping list for the hardware store. A common type of insulation employed with Retro-Line heating cables is closed cell polyethylene insulation sleeves. There are other methods of protecting these applications; consult Heat-Line for specific application requirements. As in all cases, if you are unfamiliar or uncomfortable with the measuring and or installation of a Heat-Line product please consult directly with a Heat-Line application specialist or contact a qualified local tradesperson. As such the Retro-Line system cannot be spliced together or altered in the field. For mine, the torque arrestor was in pretty good shape, as were the hose clamps that held them onto the water line. Since I knew that the well pump had been sitting in muck for who knows how long, it seemed like a good idea to shorten the length of the water tube. This means that the Retro-Line system complies with all the required health effects criteria set by NSF for plumbing heat tapes and products that are part of a potable water supply system. Occasionally these can be used on another well, but most of the time they are just scrap.
This gasket is designed for a specific casing size so the kit must be purchased for the well size — that is a 4-inch for a 4-inch well, 5-inch for a 5-inch well and so on.