Crea tu usuario en el sitio. By using a vacuum hose, technicians can quickly and easily remove debris and fluid from the engine bay. Your car may not idle right. Parts of a Triton Ford 5. If the hose looks damaged or seems to be blocked, it may be time to replace it.
The auto parts store may try to sell you fuel injection hose, that type of hose is rated to handle a lot higher PSI (pressure) and is not necessary. The term modular in this case means that the manufacturing plants can quickly change tooling in order to make another engine from this same family. Behind the fuel filter. Check the oil in 2003 Ford Expedition 5. November 27, 2021 Updated: December 16, 2022 By: Abraham Torres-Arredondo Article ID: 1261. You need to be a member in order to post a reply. Be sure to tighten the cap on the end of the new hose to ensure a good seal. This is a pain to get off and on, So it takes some patience.
When installing a car vacuum hose, make sure the new one matches the car's air pressure. 4 was used in Ford F-series trucks. Next up I replaced the L shaped hose that comes directly out the back of the throttle body and goes off toward the passenger side of the car. Spiral vacuum hoses have a U-shaped tube. Drag & drop images here. Spiral vacuum hoses are especially good for cleaning car interiors or floors. Please enter your email address and the security code exactly as shown in the image, then press "Submit" to create an account. Basically the emission line that runs over the passenger side valve cover (remember you just replaced a section of that hose earlier), well, it leads to a plastic piece of line, then this small rubber connector goes between that and another rigid plastic line. The other photo shows the U shaped piece that I removed as a unit (you need to disconnect one wiring connector, you'll see which one), and that allowed me to easily replace the small pieces and put it all back together. More: Detailed instructions on how to replace underhood vacuum hoses on Ford 4. NOTE: If you have a 1994 or 1995 4. The point is it's worth the $25 or so needed to replace the hoses to ensure reliability of your car.
Then to get it off i used the square pliers and pulled down. Monday, September 27th, 2021 AT 7:23 PM. I have no idea where it goes and think that is why my service engine light is on. Bought a 89 f150 4x4 5. o 144000 miles new bf goodrich 31/10. You definitely don't want to use heater hose on anything that will have vacuum, as the hose will collapse. There are many things that can go wrong with a Ford f150, but one of the most common problems is a vacuum leak. Yes, you can replace a vacuum hose on your Triton Ford. Yes I have a 1998 ford f150 5. More Ford E150, E250, and E350 Tutorials. Armed with this information you should open the hood and get down to a visual and tactile assessment of the hose in question.
How does a vacuum hose work? What Is the Triton Ford 5. The original hose may have been molded with the bend, however I used a straight piece of 1/4" fuel line hose and it conformed well enough for my purposes. If the gauge measurement is below 17 inches there is possibly a leak in the vacuum hose and this means you will need a new hose. If you are looking to install a Triton Ford Hose, there are a few things that you will need to do. Since writing this article, nall_one discovered an extra hose and notified me.
4 V8 engines the vacuum hose is located between the hose assembly and the vacuum reservoir. However, I was able to find a couple of things that may help. Need diagram for my truck. Unhooked vacuum line. Doing so will help to avoid any further damage and ensure that you can drive safely. If there is low or no suction, then the problem may be with the hose itself. The process will be similar for 3. Again, take the old hose off, hold it up to the new hose and cut off approximately the same length of hose. The vacuum hose on a Ford Triton car connects to the air intake on the engine. A vacuum hose is made up of several sections. It is located at the bottom of the vacuum cleaner and it directs suction force from the motor to the dustbin. Canadian Dollars (CAD$). Replace the cover on the vacuum cleaner housing.