All these methods have their different pros and cons. First and foremost, it's important to note that there's no doubt that using a foam gun to wash your car or truck is the fastest way to get the job done. Gently remove the rubber O rings on the shaft by pinching and rolling them down the shaft using your fingers. Turn the knob on the top all the way to the "negative" setting and pull the trigger on the pressure washer lance. Maintaining Your Foam Cannon. Sounds a bit exaggerated? Putting your foam cannon away full of water or full of soap creates calcium deposits which prevent the cannon from shooting the maximum amount of foam.
Simply rinse your car from top to bottom with your pressure washer, then, proceed to foaming your car. You start by foaming the first soap, a low pH acid, onto the vehicle surface. Not sure whether I have extremely hard water, (although the shampoo bubbles up just fine in my bucket) but I'm done with the foam cannon for now. A lot of factors come into play here, so let's break down some different scenarios. You can use a gas or electric pressure to shoot amazing suds, but generally, we have had the best luck with gas pressure washers. High-quality components. Whichever reason it may be, usually, the solutions are quite simple. After you have rinsed the vehicle thoroughly, replace the pressure washer tip with the foam cannon. If it's never worked well, your pressure washer might not have enough GPM or PSI. You can also check the pressure and GPM output of your washer, generally, having at least 2000 PSI provides greater foaming compared to a low pressure 1000 PSI washer. Poke a paperclip through the breather hole to ensure it's clear of any blockages. This foam cannon is the key to applying the Slick off-road wash. I put in a couple ounces of dodo juice - born to be mild, filled up the rest of the reservoir with warm water, made all the connections and pointed the "business end" of the cannon at the car.
Great packaging and great products. Here are a couple of tips to keep it in good working order: - Rinse the cannon through with only water in the bottle for a minute after you've finished washing the car to clear the chemicals. The Karcher Foam Spray Nozzle is made from plastic. They use the same kind of foam cannon soap. The top barrel has a foam head at the end which produces thick shaving cream type foam. The Foam Gun, which has car wash soap inside, connects to the end of a standard garden hose. Product Description. "But what if I need to foam more than one chemical? Sure, there is some merit to the fact that foamed car shampoo will stick to the car longer allowing the chemicals in the soap to dwell longer and work their magic. A vice is also incredibly useful, but this can be done with an extra spanner/shifter. You use a lot more soap with a foam cannon so you may not be using enough soap. Low powered, electric-driven pressure washers can sometimes not produce the amount of pressure needed to get the desired results. A Foam Cannon uses an electric or gas pressure washer, but a Foam Gun uses a regular water hose, which is the only major difference between the two devices. Pros: - Most affordable way to start foaming.
I've got the Sun Joe SPX 3000 and use Mr Pink from chemical guys. Every foam cannon operates a little differently and it can take some tinkering to find the sweet spot. Body Assembly: The metallic piece that connects and holds all the other components together. Water Pressure: Another reason your foam cannon only works upside down is the wrong water pressure – PSI (pressure per square inch) and flow rate – GPM (gallon per minute). Ready-To-Use Solution. We offer a free cannon service for anyone who has purchased our Snow Blow Cannon. Foam cannons are specialty attachments that can be used with pressure washers to create significant volumes of foam. Most bottles will have a capacity of around one liter or 32 to 33 ounces, but it's the shape of the bottle itself that you'll want to pay attention to. But differences between foam cannons vs foam guns don't stop there. Ensure secure connection before using.
Foaming your car isn't just fun, it also helps protect your car from swirls and scratches, so whether you're washing your grocery getter or your classic show car, your ride will always look its best and shine its brightest! Probably one of my best decisions when it came to maintaining my bike was buying the pressure washer foam cannon. I think everyone should try one out if they can. We recommend: - Two shifting spanners. Unscrew the round brass piece that screws onto the cannon bottle, using a pair of pliers/grips or a vice. Of your favorite soapy solution. Foam Gun vs Foam Cannon. Using a phillips head screwdriver, unscrew the blue knob on the top of the cannon. Kind of like calling a pressure washer a power washer. Our pick for the best foam cannon is the McKillans Snow Foam Cannon due to its affordability and capability.
Stepping up to a more powerful gasoline-powered pressure washer may also require matching the correct orifice. For Pressure Washer: Connect the 2-in-1 Foam Cannon unit to pressure washer wand via ¼" quick connect. That way you can go heavy on the areas that need more attention — think wheel wells and front grilles — while staying lighter across the paint and windows, for example. A single ExoForma Double Sided Microfiber Drying Towel can dry a whole vehicle completely. What else you'll need. Members who have read this thread: 0. I use 4 capfuls for SnowFoam with warm water (add warm water first, then the soap to avoid foaming inside the cannon). This pre-soak neutralizes the positively charged particles stuck to the surface.
• Safe On Paint, Plastics, And Metal Surfaces. Several catalysts are necessary to create proper, foamy suds. Does require the use of an injector. Let's dive into the difference between foam guns and foam cannons, plus how effective each option is for your situation! If you're looking for the best foam cannon car wash experience, here's what you need to know. What's the magic behind the foam cannon that generates those amazing suds? Results may vary depending on the pressure of your water source and recommended to adjust the soap to water ratio to achieve your desired result. Any thoughts on what I'm doing wrong here? 4 GPM and a maximum of 5. To access the aerator, start by pushing out the small silver pin located on the side of the front nozzle, using a small allen key or screwdriver.
This style of foam gun comes with a quick connect socket that you can attach a foam head to and then swap it for your rinse barrel when you're ready to wash off the foam. While I didn't have the opportunity to hand test all of the products in this list, I consulted consumer reviews and feedback to see how these units perform in real-world conditions. DOUBLE BARREL ALL-IN-ONE FOAM GUN WITH RINSE BARREL. Spray nozzle included. The Drive has answers. Connect wash gun adaptor for standard garden hose*. I've even tried to tip it upside down to let it mix a little more, but still requires me to use it upside down.