No need to worry about your seat angles or fiddly straps around your chest. As of 2021, all sponsorship requests should be submitted through the Sponsorships tab. The large 3″ REV2 Lite is made with bigger drivers in mind. NecksGen will refund any units that are unused and in sell-able condition within 30 days. It is extremely easy to use and can be put on outside or inside your vehicle. We've sold tens of thousands of helmets here at Competition Motorsport and, in the process of doing that, answered a million questions (probably) about them. Q: What should the gap between my upper belts behind the seat be? With simplicity and ergonomics leading the design flow, the REV 2 LITE design has no need for a frontal yoke. The NecksGen REV is a comfortable, lightweight, easy to use HNR (Head and Neck Restraint) that carries full SFI 38. Made in the USA - SFI 38. Id highly recommend buying this at any skill level as its obviously a really nice safety item to have, plus its very comfortable.
A: Yes, the NecksGen REV has been tested to the SFI flame testing standard. Q: What is the NecksGen REV made from? You must login to post a review. Sizing the REV 2 LITE is fairly simple if you use this handy chart. The backbone of the product is the patent pending Tension Neutralizing Tether (TNT). The NecksGen REV is the more affordable option for those looking for a great head and neck restraint. A2: Side Impact Protection - due to the placement and angle of the lower tether mount, the NecksGen REV unit offers unsurpassed angular impact protection. A: The NecksGen REV has inner and outer belt guides designed to keep the unit in place at all times. Combining the safety of an SFI 38. Item Requires Shipping.
Have a helper lightly pull any slack from the tether all to one side. You will have to unscrew the backing plate from the helmet hardware (backing plate is screwed to the QR helmet hardware when you buy it). Safety and Testing Questions: Q: Has the NecksGen REV passed any safety standard testing? Low-profile design significantly eases egress into/out of the car. A1: Comfort - the REV takes comfort to a new level... Our low profile design gives full range of head motion with no front or rear interference with your helmet. Q: Will NecksGen place pressure on my clavicle (collar bone)? Product Information. 0 inches total (1 inch pinch). Plus if you forget to put it on before you get in the car, its small and light enough to finagle it onto yourself even in a car with little room.
The belt channels accommodate 3 inch harnesses and have friction pads and high outer belt guides to help keep your shoulder harnesses in place while driving and even in the event of multiple impacts. Low Profile Design - The low profile design makes egress in and out of the car in an emergency easier. Padding - The shoulder and collarbone padding provide added comfort to the unit. A: No, the NecksGen REV comes with a pad that covers the contact point of the seat belt over the collar bone. View test video above.
A: The gap can be as close as 4" and as wide as 8". The Rev 2 Lite weighs only 1. The REV2 Carbon is new for 2020, and is currently the lightest head and neck restraint available. Fits necks up to 6" wide. Just select free shipping at checkout. A6: Seat Belts - the NecksGen REV Large and Medium units accomodate up to 3" seat belts. If you are on the edge between a medium and a large but have narrow shoulders, go with the medium. Q: Can I use 3" belts with my NecksGen? Tension Neutralizing Tether - Using a proprietary single tension-neutralizing tether (TNT), the loads under impact are distributed through four different load paths. A: The SFI Foundation, Inc. (SFI) is a non-profit organization established to issue and administer standards for specialty/performance automotive and racing equipment. Necksgen REV 2 Carbon Head Restraints 1 "a". The medium unit fits most adults however your neck width will determine which size you need. It works great with my pyrotect helmet and is a super versatile system.
Offers full range of motion, greatly increasing driver comfort and visibility. The medium 3″ REV2 Lite is NecksGen's most popular size. Emergency Pull - pictured separately.
1 approved, Very small, 550 grams, sits low on your body well away from your helmet, has state of the art easy to use quick release helmet hardware and of course side impact protection. The REV2 Lite is NecksGen's ultimate head and neck restraint safety device. A: No, the NecksGen unit comes with all the helmet hardware needed. What type of question would you like to submit? 3 lbs for the medium and 1 lb for the small unit (with all tethers and hardware attachments). If you purchase a helmet with the head and neck restraint, enter notes if you would like for us to install the hardware free of charge. Drivers also have different neck lengths.
A: No, the NecksGen tethers come a fixed length which has been predetermined in testing to allow proper protection. Drivers can strap in with no extra pressure on the chest or collarbones due to the REV yoke-less design. However, the NecksGen Small can only accept 2" belts. Emergency Pull - Optional pull tag for quick disconnect. Medium size REV 2 Lite. Some parts are not legal for use in California or other states with similar laws / regulations. The NecksGen units are designed and made in the USA, using the latest carbon fiber composite Dupont material.
1, Includes Helmet Hardware & Anchor Posts, Works w/ 2" & 3" Harnesses.