Training Zero turn mowers are far more maneuverable than typical riding mowers due to their unique steering capabilities. The manufacturer's directions concerning operation, maintenance, and repairs must be carefully followed. • Route the belt around the inside of the idler pulley. Pump Belt; Replacing Pump Belt; Belt Removal; Belt Installation - Yazoo/Kees ZELKH6125 Operator's Manual [Page 43. 2 bar) in the left rear tire or decrease the air pressure 2/3 psi in the right rear tire. • Before you begin refueling, minimize the risk of static electricity by touching a metal surface.
All Rights Reserved. Do not use lower grade hardware than specified. Belt tension should be set to 60-70 lbs. • Never remove gas cap or add fuel with the engine running. The belt should now be able to be removed. English-19 CONTROLS 6. Choke Control The choke control is used for cold starts in order to provide the engine with a richer fuel mixture.
Release latch and lower deck to set cutting height. Request a callback if you'd like to speak with us on the phone and be sure to include all details we would need to assist you to respect everyone's time. Come to agreement with the customer as to which additional work is to be carried out. Lubricating in Accordance with the Lubrication Schedule 1. The engine exhaust contains carbon monoxide, which is a odorless, colorless, poisonous gas. Check the sealing surface for damage. Yazoo kees illustrated parts list. General Maintenance • Never operate machine in a closed area. Procedures on contact with acid. Then lower the deck to the preset height. Disengage the brake if activated.
Move the lifting lever and check that all the chains are equally tensioned. Make the first cut relatively high; the second to the desired height. Refit the prefilter over the paper filter. IMPORTANT INFORMATION When control levers are in the reverse position they return to neutral when released. Remove nut and caster bolt. Be careful to not overtighten. 8011-732 Deck spindle English-53 LUBRICATION 4. Throttle cable Adjusting the throttle cable Checking and Adjusting the Choke Cable 1 If the engine produces black smoke or is difficult to start, this can be because the choke cable is incorrectly adjusted (upper cable). Seat adjustment bolts Fuel shut off valve in OFF position With the machine off remove the two bolts holding the seat pan down and flip the seat forward. 8011-756 Choke control 10. Yazoo Kees Replacement Parts - Farm Parts Store. 8011-730 Oil drain valve LUBRICATION Checking the Oil Level Check the oil level in the engine when the machine is standing level and the engine is stopped. Ryan started his first job in the green industry when he was 18. • Avoid starting, stopping, or turning on a slope. The resulting symptoms in hydrostatic systems may be: 1.
Amazon and eBay are great if you just need 1 or a couple of a small and light item. If you have a part number, type it into our search bar above. Accident prevention regulations, other general safety regulations, occupational safety rules, and traffic regulations must be followed without fail. Thanks for understanding. • Avoid stopping or changing speed on hills.
8011-500 Remove the dipstick The oil level should lie between the markings on the dipstick. Tighten caster bolt. After the vehicle has been used two times, the oil level should be checked while the oil is cold and adjusted accordingly. Yazoo kees drive belt diagram. • The engine's type designation (Code). English-41 MAINTENANCE Replacing the Fuel Filter Replace the line-mounted fuel filter every 100 hours (once per season) or more regularly if it is clogged.
For cold starts the control should be pulled out. IZT Bypass linkage in bypass position Bypass position English-34 MAINTENANCE Maintenance Maintenance Schedule The following is a list of maintenance procedures that must be performed on the machine. Avoid flooding water on top surface. Each person operating the mower must be of sound mind and body and must not be under the influence of any mind altering substance. The flash duration is one hour before and one hour after the interval. Create slack in the belt by removing the spring. • Mower blades are sharp. Measure the electrode gap with a gapping tool. Before performing any service or adjustment checklist: 1. 5 Linearized: Yes Page Count: 80 Has XFA: No XMP Toolkit: XMP toolkit 2. • Before and while backing, look behind and down for children. Rotate arm to release belt tension. When the transaxle operates at normal noise levels and moves smoothly forward and reverse at normal speeds, then the transaxle is considered purged.
Mower is tracking to the left. Filter access door 2. Replace elements that are damaged or bent. Mineral oil SAE 5W-30, 10W-30 can be used between -18 °C/0 °F and +5 °C/40 °F.