Next I put an adjustable (Crescent wrench) on the end of the ratchet, and tape it to hold it 'somewhat' steady (so it won't completely flop around). Make sure this nut is tight, but. While the gear tooth mesh may contribute only a small part to the looseness of the box, it is this adjustment that can remove most of the play found inside the box. Roadfly forum) about this procedure: "to adjusting the steering box: - Jack up the front of the car and with the wheels hanging and the. Any one or a combination of these symptoms is just cause to investigate the problem immediately. What Happens If You Overtighten Steering Box? Symptoms and Fixes. Manual Gear Adjustments – Shop Manual Methods. This tells me that even if you have to re-adjust after the first time i think its faster and easier not to remove so many parts.
How to adjust steering box? If the only free play you see in the steering box is rotational and the sector shaft stays centered in its housing, sometimes you can get a little more life out of it by adjusting the backlash. Carefully drive the car to check that the adjuster setting is not too tight and causing returnability problems. While you could've dropped the truck off at a shop and let them handle the job, it's never a bad idea to arm yourself with the knowledge of what it takes to diagnose and repair your own truck, and if you enjoy getting your hands dirty, you can even save yourself a pretty good chunk of change by doing it yourself. Saginaw, a division of General Motors, pioneered this design. Contributing Member. If the steering gear adjuster plug is loose or broken, it can lead to potentially dangerous driving conditions. Overtightened the adjustment screw by how much tension you feel in. What happens if you over tighten steering box set. Causes of loose steering. You may tighten them or just do nothing, this will not prolong their lifespan anymore.
It can also correct a slight misalignment of the steering shaft and gearbox. Make sure the pinch bolt is very tight (this photo was taken. The linkages connect the steering box to the wheel assemblies at the front wheels, allowing them to move back and forth when the steering wheel is turned. Steering shaft on the splines. I would suggest the following type road test: Drive the car and make ninety degree right and left hand turns at about 12 to 15 mph. The friction value is very high in this design because most of the load is concentrated on the gears at their mesh point. This is built to the same high quality as the original Mopar steering box, but inside has been upgraded with a much larger and stronger sector shaft, which makes this upgrade ideal for drivers who have larger than stock off road tires. How much is too much? steering box adjustment. I've heard you can adjust the tolerances to eliminate the wear but I have no clue if this is safe. Higher ratios mean more steering wheel movement is needed to turn the tires, although, in effect, less force is required. ManualGearC2C3AdjustInVehicleRev14NO08. Inspect the wheel bearings for lateral movement.
I've done this myself a few times with mixed results, so if an eighth to quarter turn of the adjuster screw has no impact, chances are the steering box is shot. E-mail, phone: 714-963-1558. On the topside, you'll have to disconnect the steering shaft from the box which is held on with a single bolt, and the steering shaft usually is able to slide back a few inches out of the way. Put on a 17mm crowsfoot. It is not unusual for the steering wheel to move several inches without causing the tires to actually turn at all. What happens if you over tighten steering box 2003 gmc 1500 hd. Gear lube can seep out. In the rack and pin-ion system the center rod is replaced with a steering rack which is a long, toothed bar with tie rods attached to each end. Replace upper heat shield with nut and washer on loosley until the rear slot is located into the nut then tighten. Tightening your steering gearbox too much - what may go wrong? Teeth on the ball rack engage teeth on the inner end of the sector shaft. 1963 - 1982 Corvette: Technical Article: In-Vehicle Corvette Steering Gear Adjustment. Reprinting of any portion prohibited without written permission of SK Publishing, PO Box 6983, Huntington Beach, CA 92615. This procedure will not change your front toe setting.
The steering box must have no outside drag imposed on it. If you want to improve your steering box to a level even higher than what the factory delivered, you need to check out Red-Head Steering Gears. Worm Bearing Prelude Adjustment. What happens if you over tighten steering box score. Location: Prescott Arizona. Back off the locknut on the pitman shaft, and loosen the adjuster a few turns counter clockwise to take the mesh load off the gears. Refer to the service manual for the type of recirculating ball nut steering used in the vehicle.
Steering racks are filled with oil or grease at the factory, and lubrication changes are not required.